The Federal Building Metering Guidance specifies buildings with water using processes and whole building water consumption that exceeds 1,000 gallons per day must have a water meter installed. Below are methods for estimating daily water use for typical end-uses that drive building-level, end-use water consumption.

Chat OnlineUse boiler horsepower to calculate steam flow. Boiler horsepower is not related to mechanical horsepower. It is a boiler industry rating that predicates the amount of saturated steam a boiler will generate starting with water at 212 degrees Fahrenheit and 0 pounds per square inch gauge (psig--meaning atmospheric pressure) and ending with steam at 212 F and 0 psig.

Chat OnlineA boiler fired with natural gas costing $8.00/MMBtu produces 450-pounds-per- square-inch-gauge (psig) saturated steam and is supplied with 230°F feedwater. Using values from the tables, calculate the fuel cost of producing steam.

Chat OnlineBOILER BLOWDOWN MANAGEMENT AND HEAT RECOVERY R. Scott Frazier, PhD, PE, CEM The burners are usually rated in millions of Btus per hour (e.g., 5 MMBtu/hr) but can be throttled below 1 Water-tube boilers have water inside the tubes but the principle is the same.

Chat OnlineBoiler Ratings and Boiler Load . The oldest method of rating boilers, still used to rate small boilers, is by horsepower (hp). One horsepower is defined as the ability to evaporate 34.5 lbs of water into steam at 212 deg. F and above. Large boiler capacity is generally given in lbs of steam evaporated per hour, under specified steam conditions.

Chat OnlineBLOWDOWN CALCULATION FOR BOILER This term is the most important term in boiler operation and monitoring. The parameters of the blow down are to be maintained for particular boiler. This is due to the fact that water inside the boiler gets continuously evaporated due to steam generation. Concentration of dissolve solid, inside the drum

Chat OnlineMay 04, 2016· A boiler that makes up 4000 gal/day of water having 100 ppm of hardness, has a potential of accumulating over 1000 pounds of scale per year. Alkalinity Test In natural waters, alkalinity is most commonly the result of bicarbonate and carbonate ions; in treated waters, alkalinity may also be contributed by hydroxide, phosphate, silicate, and

Chat OnlineJan 26, 2018· Best electric water boiler and warmer- reviews. I have reviewed all these products for your convenience: pros, cons, description and where to find them. Make sure you read on. 1. Zojirushi America Corporation CV-DCC50XT VE Hybrid Water Boiler and Warmer, 5-Liter, Stainless Dark Brown

Chat OnlineBoiler Horsepower - BHP. The Boiler Horsepower (BHP) is the amount of energy required to produce 34.5 pounds of steam per hour at a pressure and temperature of 0 Psig and 212 oF, with feedwater at 0 Psig and 212 oF. A BHP is equivalent to 33,475 BTU/Hr or 8430 Kcal/Hr and it should be noted that a boiler horsepower is 13.1547 times

Chat OnlineMay 04, 2016· A boiler that makes up 4000 gal/day of water having 100 ppm of hardness, has a potential of accumulating over 1000 pounds of scale per year. Alkalinity Test In natural waters, alkalinity is most commonly the result of bicarbonate and carbonate ions; in treated waters, alkalinity may also be contributed by hydroxide, phosphate, silicate, and

Chat OnlineSteam boilers tend to be steel water-tube- or fire-tube-type boilers in the 10-to-1,000-hp range. Fire-tube boilers are more robust and more tolerant of poor water quality, but require more physical space, than water-tube boilers. Regardless of boiler type, water quality is a critical aspect of implementing and operating an efficient steam plant.

Chat OnlineFor good boiler water treatment we strongly advise using HYDRAZIDE as oxygen scavenger and CONDENSATE TREAT, or CONDENSATE CONTROL, for neutralising acids in the condensate system. Initial dosage Initial dose for untreated system is 1 l of BOILER TREAT ONE SHOT per 1000 l of water.

Chat OnlineTo promote optimum performance downstream, filtration of boiler feed water streams allows an industrial boiler or power plant to meet the stringent requirements for more efficient boiler performance. Treatment of boiler feed water is required for preventing excessive heat transfer equipment fouling and erosion of

Chat OnlineApr 20, 2011· The mass won't change, so 1 kg of liquid water will form 1 kg of steam. Taking the density of water to be 1 g/cm³, you need 1 L of water to produce 1 kg of steam (in actual fact, you need a bit more, since water is not quite that dense). To make 1 ton of steam, assuming you use a metric ton, you need 1,000 L of water.: : 7How much steam does a liter of water produce - answers.comhttps:// liter of water weighs 1 kg so if it all turns to steam you will have 1 kg of steam. If the water is in an open container this will happen at 100 celsius.

Chat OnlineWhile the boiler is a powerful one, and can generate up to 225,000 pounds per hour of steam at 900 psi, the plant wont use the boiler for its heating capabilities. Instead, the plant will use their industrial steam boiler to power turbines that will create electricity.

Chat Online200 Liter Boiler Wholesale, Boiler Suppliers - Alibaba. how much liter water require for 1 hour in 3 ton boiler 200 hp boiler equals to how many tons steamboiler . US $10280-19800 located in Asia.

Chat OnlineA boiler fired with natural gas costing $8.00/MMBtu produces 450-pounds-per- square-inch-gauge (psig) saturated steam and is supplied with 230°F feedwater. Using values from the tables, calculate the fuel cost of producing steam.

Chat Online2000 liter per hour steam boiler 2019-03-27 16:56:09 About Us. Zozen Boiler main products include gas&oil boiler, coal-fired boiler, biomass boiler, thermal fluid heater and other series of more than 400 varieties of specifications.

Chat OnlineJan 31, 2013· hf = enthalpy of boiler feedwater in Btu/lb. ηB = true boiler efficiency (per ASME PTC 4.1 method) 1,000 = cost measured in units of 1,000 lbs. per hour. In this simplified calculation method, the formula assumes that one boiler is being used, one fuel and

Chat OnlineUse boiler horsepower to calculate steam flow. Boiler horsepower is not related to mechanical horsepower. It is a boiler industry rating that predicates the amount of saturated steam a boiler will generate starting with water at 212 degrees Fahrenheit and 0 pounds per square inch gauge (psig--meaning atmospheric pressure) and ending with steam at 212 F and 0 psig.

Chat Online